echemi logo
Product
  • Product
  • Supplier
  • Inquiry
    Home > Active Ingredient News > Drugs Articles > Cause analysis of filling and stoppering machine of Xilin bottle

    Cause analysis of filling and stoppering machine of Xilin bottle

    • Last Update: 2018-04-25
    • Source: Internet
    • Author: User
    Search more information of high quality chemicals, good prices and reliable suppliers, visit www.echemi.com
    The bottle moving sensor switch is not adjusted properly, the bottles are arranged too tightly, causing the bottles to move upward The friction resistance between the elastic plate and the bottle is large, which makes it difficult for the bottle to move forward The working surface of the mesh belt is uneven, and the bottle rises and falls with the rotation of the mesh belt The unevenness of the net belt support strip causes the left and right unevenness of the net belt, which causes the bottle to fluctuate up and down Too fast net belt speed is also the cause of the bottle up The corresponding treatment method can reduce the spring force properly and increase the material with small friction resistance on one side of the elastic plate, such as polytetrafluoroethylene plate, etc Flatten the net belt or use the net belt in reverse Replace the supporting strip to ensure the bottle is stable Reduce the belt speed properly The connection between the dryer and the filling and stoppering machine is in the condition of bottle missing and bottle pouring The spring force of the proximity switch is adjusted too small, which causes the proximity switch to be turned on before the bottles are squeezed tightly, so that the bottles on the mesh belt are disconnected and the bottle is inverted The installation position of the proximity switch is not correct, which causes the net belt not to stop and the bottle is empty The over plate at the outlet of the oven is too high or the over plate is uneven, resulting in the phenomenon that the bottle is empty The bottles at the bottle inlet of the big wheel are mutually squeezed, and the bottles do not rotate The position of the proximity switch and the spring force can be adjusted appropriately Readjust the position of the proximity switch The position of the transition plate can be adjusted properly, and the fault can be eliminated accordingly The bottle is broken when entering the big wheel Cylinder filling and stoppering machine Adjust the two actions of lifting and tracking, find the left and right positions of the lifting cam, fix it, adjust the tracking cam based on the action of the lifting cam, and determine the length and dimension of the connecting rod (250mm) When the lifting cam is in the descending stage at the beginning, the tracking cam action has started (the displacement distance is about 4-5mm), loosen the locking screw with the filling frame, and rotate the filling frame to Its position is right If the tracking amplitude is too large or too small, it can be corrected by adjusting the position of the long slot screw on the swing bar Adjustment of no bottle filling action and replacement of other specifications (with different equivalencies) Adjustment of no bottle filling action When the optical fiber is between * bottles and the bottle after Zui, the reset proximity switch is on, but the reset proximity switch of the optical fiber switch cannot work at the same time Each bottle is sensed by the optical fiber switch in sequence, and its corresponding equal division signal switch shall respond to the convex point (i.e the position outside the hole) of the quasi division cam When the filling slide bar component drops to the low point of Zui, the proximity switch of the control electromagnet shall respond to its corresponding signal cam The gap between the big wheel and the fence is too small, which is easy to crush the bottle There are steps between the bottle feeding net belt and the bottle walking track The net belt speed is too slow or the control part of the net belt speed has problems The radian and length of the left side fence of the bottle feeding net are not appropriate The curvature and length of the elastic plate on the left side of the bottle feeding net belt are not appropriate, and the bottle will be broken if the bottles are arranged too tightly The tooth tip chamfer of the big wheel is too large to hang the bottle, and the bottle is spit out when it just enters the big wheel.
    This article is an English version of an article which is originally in the Chinese language on echemi.com and is provided for information purposes only. This website makes no representation or warranty of any kind, either expressed or implied, as to the accuracy, completeness ownership or reliability of the article or any translations thereof. If you have any concerns or complaints relating to the article, please send an email, providing a detailed description of the concern or complaint, to service@echemi.com. A staff member will contact you within 5 working days. Once verified, infringing content will be removed immediately.

    Contact Us

    The source of this page with content of products and services is from Internet, which doesn't represent ECHEMI's opinion. If you have any queries, please write to service@echemi.com. It will be replied within 5 days.

    Moreover, if you find any instances of plagiarism from the page, please send email to service@echemi.com with relevant evidence.