Coating technology: construction method of water-based magic color art coating for interior wall

Core tip: art coating is a new type of coating that is very popular recently, especially popular among contemporary people Art coating will be selected for home decoration to create the desired effect Today, Xiaobian will take you to understand the construction process of the water-based magic art coating for the interior wall, hoping to help you decorate Key points of Construction: 1 The surface of base course is required to be flat, with moisture content ＜ 10% It is better to scrape a layer of putty with Shuangfei powder 2 Apply a layer of primer by brush or roll coating The amount of primer is 8-10 m2 and 1 kg of coating is used 3 Apply the intermediate coating with brush or roll coating method Application scope and advantages of roller ceramic coating Recommended introduction: the surface of ceramic rubber plate used for roller ceramic coating is cast into durable rubber plate by hundreds of independent small ceramic pieces Each ceramic piece has raised characteristics Under general conveyor belt pressure, thousands of unique cast bumps can produce positive traction, prevent slipping and extend the service life of conveyor belt roller At the same time, the bottom layer adopts high-quality rubber, which has strong elasticity and can play a good impact resistance role The scope of application of roller ceramic coating is one three six 83857180 (the same as V) 1 Roller coating in extremely harsh working environment 2 The belt joint is not suitable for fixing with iron buckle; 3 It is suitable for leather Paint Home News: art paint is a new type of paint that is very popular recently, especially popular among contemporary people When decorating, art paint will be chosen to create the desired effect Today, Xiaobian will take you to understand the construction process of the water-based magic art coating for the interior wall, hoping to help you decorate Key points of Construction: 1 The surface of the base course is required to be flat with a moisture content of not more than 10% It is better to use double fly powder to scrape a layer of putty 2 Apply a layer of primer by brush or roll coating The amount of primer is 8-10 m2 and 1 kg of coating is used 3 Apply a middle coat by brushing or rolling The amount of intermediate coating is 4m2 and 1kg coating is used The middle coat is a color coating, pay attention to the construction quality The drying time was 2 hours 4 The surface pattern of the construction magic color coating can be made by the following methods: (1) the scraper method surface coating is diluted with 5% - 10% water, evenly mixed, and then evenly applied on the wall surface of about 1 square meter with a brush, and then the scraper provided by the manufacturer is used to select different edges randomly, and the coating is scraped gently The angle between the scraper and the construction surface shall be small, and the handle shall be dropped and closed quickly In order to avoid surface traces, it is recommended to construct on the wall according to the sequence of drawings The amount of surface coating is 6-8 m2 and 1 kg of coating is used When the pattern of 1 square meter is completed, the painting construction of the next 1 square meter shall be started until all the patterns are completed Sequence of painting lines: 1 25 3 4 8 6 7 9 (2) the surface painting method is diluted with 5% - 10% water, evenly mixed, and then evenly painted on the wall surface of about 1 square meter with a brush, and then painted with a brush according to the selected figure Pay attention to the importance of the brush when brushing the pattern, and the speed of falling and closing It is suggested to construct in the order of the drawings (3) The roll coating method is the same as the scraper method and brush coating method Firstly, the diluted surface is evenly coated on the wall, and then, the roller provided by the manufacturer is used to roll coating in the vertical direction from the bottom to the top During roller coating, the force shall be even and the line shall be long, and roller coating shall not be conducted back and forth (4) Seal method (sponge) first apply the diluted surface evenly on the wall surface, and then stick the sponge flowers on the painted wall surface, and then lift them up and repeat the action for many times Note that the sponge can not rotate when it is glued down, and there should be no gap and galling between patterns Sponge flower method: wet the sponge slightly with water, fold the two or more layers alternately, bind it from the center, make a proper pattern according to the requirements, and print on the surface Home of coatings is specialized in coatings, diatom mud, paint coating, coating technology, fire retardant coating news and coating, diatom mud, paint coating, coating technology, fire retardant coating decoration knowledge and decoration renderings,