Common knowledge of coating: Problems and solutions in stone like paint construction

Core tip: stone like paint is often used in decoration, but the specific construction problems of stone like paint are unfamiliar to many consumers Here is a brief introduction of the problems and solutions in the construction of stone like paint Imitated stone paint, also known as imitated stone paint, is the exterior wall paint imitated stone and imitated natural stone Its effect is vivid On texture or color, it is close to natural stone, but slightly lacking in hardness Stone like paint is fire-proof, water-proof, acid and alkali resistant, pollution-resistant, non-toxic, tasteless, strong adhesive force, never fade, etc., which can be effectively prevented Paint knowledge | precautions for wall paint color selection Recommended introduction: when painting the wall, the owner sometimes has difficulty in choosing what color of the wall paint to paint In fact, there is no ugly color in the wall paint, only the disharmonious color matching The use of wall color contains the knowledge of health Too strong color will stimulate people's perception, make people have a sense of fidgety, affect people's mental health Grasp the basic principles of wall color and paint a colorful space 1、 Wall paint color selection notice 1 Light color is generally used for the top surface Light colors make people feel light, dark colors make people feel heavy Usually, the treatment of rooms is from top to bottom, from shallow to deep For example, the ceiling and walls of rooms are white and Home of paint news: stone like paint is often used in decoration, but the specific construction problems of stone like paint are unfamiliar to many consumers Here is a brief introduction of the problems and solutions in the construction of stone like paint Imitated stone paint, also known as imitated stone paint, is the exterior wall paint imitated stone and imitated natural stone Its effect is vivid On texture or color, it is close to natural stone, but slightly lacking in hardness Stone like paint has the characteristics of fire prevention, waterproof, acid and alkali resistance, pollution resistance, non-toxic, tasteless, strong adhesive force, and never fade, etc., which can effectively prevent the external environment from eroding the building and extend the life of the building At the same time, stone like paint has good adhesion and freeze-thaw resistance, so it is particularly suitable for use in cold areas At present, the imitation stone paint is superior, and it is more and more popular in villas, commercial houses, office buildings, etc The possible problems in the construction of stone like paint are mainly cracks The following aspects should be paid attention to in the construction process Internal and external corner cracks: during the spraying process of fluorocarbon paint, sometimes there will be cracks at the internal and external corners, because the internal and external corners are two sides If the real stone paint is sprayed, there will be two different directions of tension acting on the film at the internal and external corners at the same time during the drying process, which is easy to crack On site solution: if the internal and external corners of the cracks are found, spray again with a thin spray gun every half an hour until the cracks are covered; for the internal and external corners of the new spray, pay special attention not to spray the thickness once, adopt the thin spray multi-layer method, that is, spray again after the surface is dry, the distance between the spray guns should be far, the movement speed should be fast, and the vertical internal and external corners should not be sprayed, only scattered Shoot, i.e spray two sides to let the edge of the spray flower sweep into the internal and external corners Plane cracks: the main reason may be that the weather temperature difference is large and suddenly becomes cold, resulting in different drying speed of the inner and outer layers If the surface is dry and the inner layer is not dry, cracks will be formed The solution on site is to use a small nozzle spray gun, spray thin layers, try to control the drying speed of each layer, and the spraying distance is a little longer Cracks appear in the film forming process: when spraying, the coverage is not uniform or too thick, cracks appear after the film forming on the coating surface, or even cracks appear several weeks later This situation needs to be analyzed in detail In addition to paying attention to the spraying method during construction, the formula shall be changed if necessary, and trial production shall be carried out again Home of coatings is specialized in coatings, diatom mud, paint coating, coating technology, fire retardant coating news and coating, diatom mud, paint coating, coating technology, fire retardant coating decoration knowledge and decoration renderings,