Epoxy flattening flooring is based on the addition of epoxy mortar flooring

Epoxy mortar flooring is mainly in the epoxy flat surface construction on the basis of the addition of a layer or several layers of epoxy mortar, so that the ground can be very good for a rough leveling, so that the original potholed ground can do the overall flat, while anti-pressure wear anti-penetration to excellent and epoxy thin coating flooring, the following is the epoxy mortar floor construction program:
1, grinding clean ground. Use a grinder to smooth the uneven ground, if there is a depression place to fill with cement or putty, in the sanding, to make the whole ground smooth and dust-free, which is a basic way to do a good job of floor paint.
2, stir
the
. The raw materials must be mixed and stirred to be used, and epoxy primers, epoxy finishes, putty powders, epoxy quartz mortars and their corresponding curing agents are used during construction, all of which require mixing and mixing to be used. For example, the mixing ratio between epoxy primers, varnishes, and medium paints and curing agents is 4:1, especially in summer, pay more attention to their mixing ratio, summer to pour a small amount of curing agent, mixing ratio is about 5:1. Mixing between quartz sand and water in quartz mortar and mixing between putty powder and water are to be matched and stirred in the corresponding process.
3, coat the bottom. Here needs to be epoxy primer, the use of epoxy primer to close the ground, so that the ground moisture and air can not reach the ground, in the coating of the bottom should also pay attention to the smoothness of the ground.
4, scrape more than twice epoxy quartz mortar. Quartz sand and putty servings are used to level the floor and increase the coating thickness to increase the wear resistance of the floor. Because quartz sand fillers are rough, so the floor paint mortar layer is relatively rough, there are more fine holes, the first mortar can effectively find flat floor paint construction substation.
5, scrape the paint putty once. Putty is painted behind quartz sand mainly to find a flat quartz sand layer, because the quartz sand layer gap is relatively large, so putty has played such an effect.
6, polished flat, vacuuming.
7, paint. Color paint is mainly epoxy paint, epoxy paint many kinds, not only color and its light effect is also different. This is determined by the color of the customer's needs.
Shenzhen Guoping Flooring Company pointed out that epoxy flat cement substation is solid, strong, shellless, should put an end to the phenomenon of mortar shelling, concrete layer and mortar to find a flat layer should be poured together. If the concrete layer is poured first, the thickness of the mortar layer is not less than 40mm, and the requirements for the fork lane are thicker. The slope should meet the design requirements, allowing the deviation value to be 2 and not greater than 30mm. Hangzhou epoxy flat coating manufacturers pointed out that epoxy flat coating requires the surface can not be sand, high hardness, there is no cement powder phenomenon. Newly poured cement mortar layers should be fully maintained. Cement substation is flat, no bumps, honeycomb hemp, cement, other paint, latex paint, bubblegum and other residues. Hangzhou epoxy flat coating manufacturers pointed out that for water-based epoxy resin coatings, whether its curing is adequate mainly depends on the following two factors:
First, epoxy dispersion phase particle size, in order to ensure that the water-based epoxy curing agent dosage is the same, epoxy resin When the particle size of the dispersed phase particles is small, the curing agent concentration of the particle surface is moderate, the surface curing speed is slower, the curing agent molecule has enough time to spread to the whole epoxy dispersion phase particles, so that it cures completely, so that a uniform, completely cured coating film can be formed;
2 is the compatible between epoxy curing agent and epoxy resin, Hangzhou epoxy flat coating manufacturers pointed out that improving the compatible between epoxy curing agent and epoxy resin, is conducive to the stability of the water-based epoxy emulsion dispersion system, and the better the compatible between the two, the easier the epoxy curing agent to the internal diffusion of epoxy resin particles, conducive to the curing reaction.
epoxy flat coating can be said to be the current level of the world's incense, with the promotion of recent years and market feedback, has been gradually accepted and recognized by everyone. Not only is the ordinary cement floor, there are many customers in the floor after the finish of gold sand wear-resistant bone or abrasive stone, and then use Litek or Baoboli epoxy flat coating to improve the wear resistance and sealing and gloss of the floor, so that the floor more beautiful, wear-resistant and longer life. Hangzhou epoxy flat coating manufacturers pointed out that because the concrete floor, gold sand floor and water mill floor is not sealed, oil stains, stains, and some solvents can easily seep into the inside of the floor, especially difficult to thoroughly clean up these oil, the floor is very unsightly. Hangzhou epoxy flat coating manufacturers pointed out that after the sealing curing treatment, the surface of the floor is sealed, oil is not easy to penetrate into the inside of the floor, after the time to clean up, almost no trace of oil pollution.
。