-
Categories
-
Pharmaceutical Intermediates
-
Active Pharmaceutical Ingredients
-
Food Additives
- Industrial Coatings
- Agrochemicals
- Dyes and Pigments
- Surfactant
- Flavors and Fragrances
- Chemical Reagents
- Catalyst and Auxiliary
- Natural Products
- Inorganic Chemistry
-
Organic Chemistry
-
Biochemical Engineering
- Analytical Chemistry
- Cosmetic Ingredient
-
Pharmaceutical Intermediates
Promotion
ECHEMI Mall
Wholesale
Weekly Price
Exhibition
News
-
Trade Service
How much do you know about the maintenance of the reactor? The reactor is a common laboratory instrument, and it has various types, such as double-layer glass reactor, single-layer glass reactor, stainless steel reactor, etc.
, but no matter what type of reactor, daily maintenance is essential of
.
Let's follow the editor's instrument to understand what are the maintenance instructions for the reactor
.
Maintenance Instructions: 1.
Carefully check the instrument before use, whether the glass bottle is damaged, whether the interfaces are consistent, and pay attention to handle it with care
.
2.
Wipe each interface with a soft cloth (can be replaced with a napkin), and then apply a little vacuum grease
.
(Be sure to cover the vacuum grease after use to prevent lime and sand from entering
.
) 3.
Each interface should not be over-tightened, and should be loosened regularly to avoid long-term locking to prevent the connector from being bitten
.
4.
Turn on the power switch first, and then let the machine run from slow to fast.
When the machine is stopped, keep the machine in a stopped state, and then turn off the switch
.
5.
The PTFE switches everywhere should not be over-tightened, which will easily damage the glass
.
6.
After each use, use a soft cloth to wipe off all kinds of oil stains, stains and solvent left on the surface of the machine to keep it clean
.
7.
Unscrew each PTFE switch after stopping, and the PTFE piston will be deformed if it is still in the working state for a long time
.
8.
Regularly clean the sealing ring, the method is: remove the sealing ring, check whether there is dirt on the shaft, wipe it with a soft cloth, then apply a little vacuum grease, and reinstall it to keep the shaft and the sealing ring smooth
.
9.
The electrical part must not enter the water, and it is strictly forbidden to get wet
.
10.
When doing any repairs or inspections on the machine, be sure to cut off the power and water first
.
Note that this equipment is a fragile product, please handle it with care when using it.
Damage to fragile products is not within the scope of our warranty.
If the customer needs it, our company will charge the corresponding cost
.
The above is the relevant introduction to the maintenance instructions of the reaction kettle.
I hope you will have a corresponding understanding of this after reading, and hope it will be helpful to you
.
, but no matter what type of reactor, daily maintenance is essential of
.
Let's follow the editor's instrument to understand what are the maintenance instructions for the reactor
.
Maintenance Instructions: 1.
Carefully check the instrument before use, whether the glass bottle is damaged, whether the interfaces are consistent, and pay attention to handle it with care
.
2.
Wipe each interface with a soft cloth (can be replaced with a napkin), and then apply a little vacuum grease
.
(Be sure to cover the vacuum grease after use to prevent lime and sand from entering
.
) 3.
Each interface should not be over-tightened, and should be loosened regularly to avoid long-term locking to prevent the connector from being bitten
.
4.
Turn on the power switch first, and then let the machine run from slow to fast.
When the machine is stopped, keep the machine in a stopped state, and then turn off the switch
.
5.
The PTFE switches everywhere should not be over-tightened, which will easily damage the glass
.
6.
After each use, use a soft cloth to wipe off all kinds of oil stains, stains and solvent left on the surface of the machine to keep it clean
.
7.
Unscrew each PTFE switch after stopping, and the PTFE piston will be deformed if it is still in the working state for a long time
.
8.
Regularly clean the sealing ring, the method is: remove the sealing ring, check whether there is dirt on the shaft, wipe it with a soft cloth, then apply a little vacuum grease, and reinstall it to keep the shaft and the sealing ring smooth
.
9.
The electrical part must not enter the water, and it is strictly forbidden to get wet
.
10.
When doing any repairs or inspections on the machine, be sure to cut off the power and water first
.
Note that this equipment is a fragile product, please handle it with care when using it.
Damage to fragile products is not within the scope of our warranty.
If the customer needs it, our company will charge the corresponding cost
.
The above is the relevant introduction to the maintenance instructions of the reaction kettle.
I hope you will have a corresponding understanding of this after reading, and hope it will be helpful to you
.
