echemi logo
Product
  • Product
  • Supplier
  • Inquiry
    Home > Active Ingredient News > Drugs Articles > How to use automatic liquid filling machine

    How to use automatic liquid filling machine

    • Last Update: 2022-06-18
    • Source: Internet
    • Author: User
    Search more information of high quality chemicals, good prices and reliable suppliers, visit www.echemi.com

    How to use Shanghai Shenggang automatic liquid filling machine: 1.
    Before the machine works, the ground wire must be well grounded, and then select the appropriate standard syringe according to the different filling volumes

    .

    The general dispensing range is 0.
    2-1ml with a 1ml syringe; 1-5ml with a 5ml syringe; 5-10ml with a 10ml syringe; 20ml model, use a 20ml glass syringe; 100ml model, use a 100ml glass syringe, 500ml The model uses the stainless steel filling system produced by our factory

    .


    2.
    Pull out the inner core of the syringe and put the screw sleeve on the inner core of the syringe (Note: the 10ml model needs to select the gasket according to the size of its outer circle due to the large difference in the diameter of the syringe) and properly tighten it with the lower base with the screw sleeve (The disassembly and assembly of the syringe must pay attention to cleaning)

    .


    3.
    Put the upper clamp seat on the water outlet end of the syringe jacket, and properly tighten the nuts on both sides (when using a 5ml syringe, put the bushing on and tighten it together, pay attention to tightening it too tightly, the outer sleeve is fragile)

    .

    Note: The 10ml model has an adjustment sleeve, but the 20, 100, and 500 models do not
    .


    4.
    Assemble the inner core and outer jacket of the installed syringe into one, and the liquid injection system is now assembled

    .


    5.
    Turn the valve arrow up and the arrow mark outward to fix it on the fixing screw with a nut

    .


    6.
    Assemble the complete liquid injection system, and align the upper and lower round holes of the liquid injection system components with the upper and lower fixing rods, respectively, and put them on the bearing, and make the outer end surface and the bearing surface level

    .

    When the lower end is assembled, do not make the screw sleeve and the crank collide to prevent abnormal noise when the upper crank rotates (the distance between the screw sleeve and the crank is about 1mm when installed correctly).
    After the injection system is installed correctly, tighten the upper and lower parts.
    Set screws

    .

    Use a short hose to connect the syringe to the valve connector
    .

    The liquid inlet pipe is connected to the water inlet, and the liquid outlet pipe is connected to the water outlet
    .

    To prevent the inlet and outlet pipes from being entangled, snap the inlet and outlet pipes into the side lugs of the casing
    .

     7.
    Turn the crank by hand, it should be able to rotate freely, otherwise the assembly is wrong, and you should check whether the injection system is fastened on the rotating bearing

    .


    This article is an English version of an article which is originally in the Chinese language on echemi.com and is provided for information purposes only. This website makes no representation or warranty of any kind, either expressed or implied, as to the accuracy, completeness ownership or reliability of the article or any translations thereof. If you have any concerns or complaints relating to the article, please send an email, providing a detailed description of the concern or complaint, to service@echemi.com. A staff member will contact you within 5 working days. Once verified, infringing content will be removed immediately.

    Contact Us

    The source of this page with content of products and services is from Internet, which doesn't represent ECHEMI's opinion. If you have any queries, please write to service@echemi.com. It will be replied within 5 days.

    Moreover, if you find any instances of plagiarism from the page, please send email to service@echemi.com with relevant evidence.