echemi logo
Product
  • Product
  • Supplier
  • Inquiry
    Home > Chemicals Industry > Chemical Technology > Introduction to the causes and treatment methods of copper wire yellowing in wire and cable

    Introduction to the causes and treatment methods of copper wire yellowing in wire and cable

    • Last Update: 2022-11-22
    • Source: Internet
    • Author: User
    Search more information of high quality chemicals, good prices and reliable suppliers, visit www.echemi.com

    In a sense, the wire and cable manufacturing industry is an industry
    of material finishing and assembly.
    First, the amount of materials used is huge, and the material cost in cable products accounts for 80-90% of the total manufacturing cost; Second, there are many types and varieties of materials used, and the performance requirements are particularly high, such as copper for conductors, the purity of copper is required to be more than 99.
    95%, and some products should use oxygen-free high-purity copper; Third, the selection of materials will have a decisive impact
    on the manufacturing process, product performance and service life.
    Among them, the selection of copper wire is particularly important, if the slightest carelessness may cause safety accidents
    .
    Below, the editor will sort out some of the causes and treatment methods of yellow copper wire
    .

    Yellowing usually has several causes:

    1.
    The temperature of the tin furnace is too high and the fluidity is large, resulting in too large the pinhole of the plating and fast penetration of copper and tin

    2.
    The tin layer is too thin, and the copper and tin penetrate quickly

    3.
    There are too many flux halogen residues, and the pickling on the copper surface is not thorough enough

    4.
    The packaging time is too fast, the heat is not dissipated, and the tin furnace impurities are too much

    5.
    The quality of copper is not good, and there are too many impurities

    6.
    The temperature has an effect on the activity of copper atoms, and hot days turn yellow faster
    than cold days.

    These issues can be addressed
    in the following ways.

    1.
    Mold aperture> wire warp +0.
    02mm (the purpose is very simple, can not be too thin);

    2.
    After production, it can be placed for about 2 hours and then packaged (purpose: internal heat dissipation);

    3.
    Buy a good flux, match the flux concentration, mainly the flux affects the quality of tin plating;

    4.
    Choose a better oxygen-free copper wire
    .

    In a sense, the wire and cable manufacturing industry is an industry
    of material finishing and assembly.
    First, the amount of materials used is huge, and the material cost in cable products accounts for 80-90% of the total manufacturing cost; Second, there are many types and varieties of materials used, and the performance requirements are particularly high, such as copper for conductors, the purity of copper is required to be more than 99.
    95%, and some products should use oxygen-free high-purity copper; Third, the selection of materials will have a decisive impact
    on the manufacturing process, product performance and service life.
    Among them, the selection of copper wire is particularly important, if the slightest carelessness may cause safety accidents
    .
    Below, the editor will sort out some of the causes and treatment methods of yellow copper wire
    .

    Wire and cable

    Yellowing usually has several causes:

    1.
    The temperature of the tin furnace is too high and the fluidity is large, resulting in too large the pinhole of the plating and fast penetration of copper and tin

    2.
    The tin layer is too thin, and the copper and tin penetrate quickly

    3.
    There are too many flux halogen residues, and the pickling on the copper surface is not thorough enough

    4.
    The packaging time is too fast, the heat is not dissipated, and the tin furnace impurities are too much

    5.
    The quality of copper is not good, and there are too many impurities

    6.
    The temperature has an effect on the activity of copper atoms, and hot days turn yellow faster
    than cold days.

    These issues can be addressed
    in the following ways.

    1.
    Mold aperture> wire warp +0.
    02mm (the purpose is very simple, can not be too thin);

    2.
    After production, it can be placed for about 2 hours and then packaged (purpose: internal heat dissipation);

    3.
    Buy a good flux, match the flux concentration, mainly the flux affects the quality of tin plating;

    4.
    Choose a better oxygen-free copper wire
    .

    This article is an English version of an article which is originally in the Chinese language on echemi.com and is provided for information purposes only. This website makes no representation or warranty of any kind, either expressed or implied, as to the accuracy, completeness ownership or reliability of the article or any translations thereof. If you have any concerns or complaints relating to the article, please send an email, providing a detailed description of the concern or complaint, to service@echemi.com. A staff member will contact you within 5 working days. Once verified, infringing content will be removed immediately.

    Contact Us

    The source of this page with content of products and services is from Internet, which doesn't represent ECHEMI's opinion. If you have any queries, please write to service@echemi.com. It will be replied within 5 days.

    Moreover, if you find any instances of plagiarism from the page, please send email to service@echemi.com with relevant evidence.