echemi logo
Product
  • Product
  • Supplier
  • Inquiry
    Home > Active Ingredient News > Drugs Articles > Labeling machine debugging steps

    Labeling machine debugging steps

    • Last Update: 2022-05-03
    • Source: Internet
    • Author: User
    Search more information of high quality chemicals, good prices and reliable suppliers, visit www.echemi.com
    Debugging steps of labeling machine: 1.
    Adjustment of labeling station
    .

    Adjustment of the squeegee and the rubber roller: There can be no gap between the squeegee and the rubber roller in the entire length.
    If there is a gap, the squeegee can be adjusted by adjusting the eccentric bolts
    .

    Adjustment of the rubber roller and the target plate: The target plate and the rubber roller are only in contact with each other without any pressure
    .

    The gap is too large, and the glue on the target plate is too much, resulting in glue rejection
    .

    If the gap is too small and the contact is too tight, the glue will be squeezed away, and there is no glue on the half of the target board
    .

    Practice has proved that the gap between the target plate and the rubber roller is between 0.
    1mm and 0.
    2mm
    .

    It can be achieved by adjusting the bearing seat on the lower part of the rubber roller, and if necessary, adjust the bearing on the upper part of the rubber roller
    .

    2.
    Adjustment of the label box
    .

       The center line of the standard box, the center axis of the standard station is tangent to the label paper, the three points of the center axis of the target plate are in a line, adjust the tangent between the target plate and the label paper (0 distance), and then move the standard box closer to 1mm ~ 2mm
    .

    The gap between the standard paper in the standard box and the pressure bars on both sides should be between 0.
    8mm-1mm.
    If the gap is too large, the standard paper will be displaced in the standard box, and oblique marks will appear.
    If the gap is too small, the standard push will be difficult
    .

    Adjustment of the position of the grabbing hooks of the standard box: the upper and lower, left and right grabbing hooks are on the same vertical plane and work evenly on the standard paper, so that the mark can be grasped smoothly
    .

    Adjustment of the label feeding roller: When there is no label, the label pressing plate can be pressed to the front end of the label box and when the label is loaded, the label near the label hook finger cannot be crushed
    .

       3.
    The adjustment of the bottle feeding star wheel, the bottle feeding star wheel and the bottle feeding screw rod
    .

       When adjusting the bottle-in, bottle-out star wheel and bottle-feeding screw rod, the bottle pressing head of the labeling machine shall prevail
    .

    First adjust the bottle feeding star wheel.
    When the bottle pressing head just presses the bottle, adjust the bottle feeding star wheel so that the bottle is located in the middle of the star wheel groove
    .

    Adjustment of the bottle feeding screw: Take the bottle feeding star wheel as the criterion.
    When the bottle is in the middle of the groove of the bottle feeding star wheel, adjust the screw rod so that the bottle feeding side of the screw rod is close to the bottle without displacement
    .

    Adjustment of the bottle star wheel: When the bottle press head is just lifted, adjust the star wheel so that the bottle is in the middle of the groove of the star wheel
    .

     
    This article is an English version of an article which is originally in the Chinese language on echemi.com and is provided for information purposes only. This website makes no representation or warranty of any kind, either expressed or implied, as to the accuracy, completeness ownership or reliability of the article or any translations thereof. If you have any concerns or complaints relating to the article, please send an email, providing a detailed description of the concern or complaint, to service@echemi.com. A staff member will contact you within 5 working days. Once verified, infringing content will be removed immediately.

    Contact Us

    The source of this page with content of products and services is from Internet, which doesn't represent ECHEMI's opinion. If you have any queries, please write to service@echemi.com. It will be replied within 5 days.

    Moreover, if you find any instances of plagiarism from the page, please send email to service@echemi.com with relevant evidence.