Operation procedures and precautions of flat aluminum plastic packaging machine

The flat aluminum plastic packaging machine has three functions of aluminum / plastic, aluminum / aluminum, aluminum / plastic / aluminum, etc it is suitable for aluminum / plastic, aluminum / aluminum, aluminum / plastic / aluminum packaging of tablets, capsules and other special-shaped pieces Main features: 1 The fuselage is packaged in a separate way, which is convenient for the user to enter the elevator and the separate purification workshop When merging, the cylinder pin is fixed with screws for positioning, and the assembly is simple 2 Worm gear reducer, overload protection of main engine, lower noise, stable operation 3 The stroke can be adjusted, and the size of the plate can be changed at will, which is suitable for products of various specifications 4 Online detection and rejection of defective products, rejection rate is over 99.9% (optional) 5 Adopt double shaft positioning and (spline) shaft drive, work synchronously and stably 6 Adopt PLC programmable modular design of display screen, simple and reliable operation, convenient maintenance (optional) So how to operate such a good device? What are the precautions during operation? Let's have a look at it together Operation procedure 1 Turn on the electric green indicator light, turn the upper and lower heating switches of the forming and the heat seal to the "on" position respectively, the worktable and the temperature controller control the forming temperature, generally preset 90C ˚ and 100C ˚, the second temperature controller heat seal, preset 120c ˚ - 140C ˚ up and down, and preset the temperature of the forming and heat seal temperature controller as appropriate 2 Put down the upper pressing block of the feed roller, the temperature of the forming heating plate is in place, and then open the main machine The plastic PVC is formed first, and the position of the forming blister is consistent with that of the heat sealing mold hole Pay attention to the heat sealing mold base to put down the heat sealing mold with the handle to press the aluminum foil, and the aluminum foil will be driven to the blanking Observe whether the movement of the plastic (refers to the formed PVC on the machine board) is shifted left and right If there is deviation, adjust the starting and guiding roller seat to adjust the starting and guiding direction 3 If the aluminum foil moves to the left and right, adjust the hand wheel of the knuckle roller seat If the front and rear deviation is adjustable, the box can move 4 After the hot sealing and blanking is normal, properly open the feeder ram so that the medicine (tablet capsule and sugar coating) can enter the feeding room properly If there is a small amount of missing grain, it can be filled manually When filling the grain, the first precautions are: rolling hand of roller press roll and breaking the aluminum foil by hook In addition, if there is missing grain when the forming blister passes the roller edge, do not force to fill again When the medicine is brought in, it will seriously affect the synchronization, Light this in the aluminum foil when sealing the mold, to set processing 5 Due to the increase of the weight of the medicine, the tension of the aluminum foil and the gradual change of the temperature of the machine are not equal, which may cause the asynchronous phenomenon of forming and heat sealing, leading or lagging First, check whether the plastic PVC and the aluminum foil have a negative separation, and then use the fine-tuning mechanism on the machine to adjust The fine adjustment mechanism moves forward and backward in the mold because it adjusts the distance or adjusts the box front and back Therefore, before starting the machine, it should be placed in the neutral position to move forward and backward It can also be adjusted by moving the front box After the correct movement, the plate will not be correct until more than ten versions have been completed Therefore, when not finished, do not adjust it randomly 6 The heat sealing quality of plastic aluminum foil (uniform, firm and flat adhesion) is demonstrated by temperature or pressure, and the flatness of chequered plate If there is a bad heat sealing, it is generally suitable for temperature, general temperature, slightly lower pressure, temperature adjustment and screw pressure adjustment 7 Offset of punching, offset of cutting with layout, stop machine and move the manually adjusted box, the die can be adjusted 8 In daily operation knowledge, for operation work, it is necessary to know the structural principle of the machine The roller of the ejector seat is driven by the cam, the up and down travel, the position of the upper cover template is fixed, and the bubble cover is in a bad state Pay attention to the lower forming die or heat seal to the top dead point, and fasten the column nut If you don't pay attention, it's easy to break down The roller needle of the ejector seat is locked, and the troubleshooting method The precautions are as follows: 1 Do not install There are rubber wheels under the base, which can be moved 2 Full time personnel training operation and maintenance 3 The grounding wire shall be connected according to the specified position of the grounding label 4 The machine should be kept clean 5 All parts of the machine must be refueled before production (refer to the operation regulations) 6 When the machine leaves the factory, the transmission case gauge belt lubricating oil must be refueled before production 7 It is suggested to use oil-free air compressor as far as possible 8 Forming, heat sealing, indentation and other parts of the pressure should not be too large, or affect the service life There should be a floating space of about 1mm for the type pad rotation of forming indentation The above is all about the operation procedures and precautions of the flat aluminum plastic packaging machine that I share with you today I hope it can help you.