echemi logo
Product
  • Product
  • Supplier
  • Inquiry
    Home > Biochemistry News > Biotechnology News > Polyclonal Antibody Production

    Polyclonal Antibody Production

    • Last Update: 2020-10-26
    • Source: Internet
    • Author: User
    Search more information of high quality chemicals, good prices and reliable suppliers, visit www.echemi.com

    Your antigen should at least have a molecular weight of 20 KDa for development of a strong immune response in animals. If it is a small protein , it can be linked to a larger protein by chemical methods or cloned and expressed as a fusion protein with a larger protein. If it is a peptide or small molecule, a carrier-hapten conjugate must be made. Purify your antigen well to obtain antibodies with good specificity.

    Obtain at least two 6 week old New Zealand White Rabbits and have them delivered to the ARC. Don’t put all your eggs in one basket only using one rabbit. Let them get accustomed to there home there for two weeks before the first pre-bleed.

    Pre-bleed

    1. Calmly and gently place rabbit in a restrainer. If they are relaxed they bleed much easier.

    2. With a razor blade, shave the top middle of the ear you wish to bleed, completely exposing the large vein running down the center of the ear.

    3. If you find it necessary, dilate the ear vein by rubbing xylene on it witha Q-tip.

    4. Using a perfusion kit with a butterfly needle at one end and a rubber enclosed needle at the other, insert the butterfly needle in the vein. Immediately after blood is seen in the tubing, quickly insert the needle at the other end into the rubber cork of a 20 mL evacuated blood collection tube. This step works best with two people.

    5. When you have the required amount of blood (1-5 mL is sufficient for a pre-bleed�for later bleeds take 20 mL), remove the needle and apply pressure to the wound. When the bleeding has stopped (~10 seconds), sterilize the ear with ethanol. If you used xylene, rinse two or three times with ethanol to remove it.

    6. Remove the rabbit from the restrainer and place in its cage.

    7. Take the collected blood and place at 37 °C for 30 minutes to inactivate complement.

    8. Ring the inside walls of the tube with a glass pipet and place at 4 °C overnight to clot.

    9. Decant the clotted blood into a centrifuge tube and centrifuge at 4 °C 10,000g for 10 minutes (the blood collection tubes will shatter!).

    10. Decant or pipet off the supernatant. This is your serum. Dispose of all blood waste in appropriate biohazardous containers.

     

     

    Antigen Injection

     

     

     

     

    1. For injection of two rabbits, your antigen should be in 1 mL of a buffer such as PBS or Tris that contains no chemicals harmful to the rabbit. 100 µg/rabbit of antigen is best, but you can use less and get good results.

    2. Again for two rabbits, prepare RIBI adjuvant by warming in a beaker of warm water, injecting 1 mL of sterile saline and 1 mL of your antigen solution, and vortexing vigorously for 2 minutes to get a good suspension. Do not get adjuvant in your eyes, or anywhere else.

    3. Calmly take the rabbit out of its cage, reassuringly petting it. There is no need for a restrainer. Place on a flat surface for the injection. With a 1 mL syringe, draw in 1 mL of your antigen/adjuvant solution. Four subcutaneous injections are done; two on the lower back and two on the thigh. To inject, rub the hair away from the injection site and sterilize with a squirt of ethanol. Pinch the skin and pull up slightly to pull the skin away from the muscle, insert the needle 1-2 cm at a shallow angle so as to not hit muscle, and inject 250 µL of your innoculum. After the required volume has been injected, let the needle sit for a few seclonds, then pull out and gently rub the injection site so nothing leaks out. Repeat for all four sites and place the rabbit back in its cage. Now do your other rabbits.

    4. Injections will be done every 4-6 weeks, with bleeds 7-10 days after each injection. Bleeds are performed identically to the pre-bleed, but get at least 20 mL per rabbit, with 40 mL being the upper limit for an adult rabbit (any more and they get anemic).

    <fo

    This article is an English version of an article which is originally in the Chinese language on echemi.com and is provided for information purposes only. This website makes no representation or warranty of any kind, either expressed or implied, as to the accuracy, completeness ownership or reliability of the article or any translations thereof. If you have any concerns or complaints relating to the article, please send an email, providing a detailed description of the concern or complaint, to service@echemi.com. A staff member will contact you within 5 working days. Once verified, infringing content will be removed immediately.

    Related Articles

    Contact Us

    The source of this page with content of products and services is from Internet, which doesn't represent ECHEMI's opinion. If you have any queries, please write to service@echemi.com. It will be replied within 5 days.

    Moreover, if you find any instances of plagiarism from the page, please send email to service@echemi.com with relevant evidence.