Setting of temperature and humidity for the use of mold culture box

mold incubator is a kind of incubator, mainly cultured organisms and plants, in the confined space set the corresponding temperature, humidity, so that mold in 4-6 hours or so long out, as an artificial acceleration of the use of mold, to assess the resistance of electrical electronic products and mold degreeIt is an important detection method in the artificial three-proof climate, and it is the necessary testing equipment of scientific research laboratory for storage of strains, biological culture and research laboratory in tertiary institutions, medicine, military industry, electronics, chemical industry and biological researchUsed to test and judge its parameters and performance after changes in the humid heat temperature environmenthow to set the temperature and humidity of the mold incubator
(i) temperature/time key can be temperature and time switching:1) temperature setting: press the temperature/time key, the meter temperature setting light is onPress the set key to enter the SV state, and then press the button to change the temperature setting to the desired temperature (zui small value 0 degrees C), and then press the set key to deposit the set value into the microcontroller, at this time the left display window shows the measurement temperature, the right display window shows the set temperature2) time setting: press the temperature/time key, the meter's time setting indicator is onPress the set key to enter the TV state and then press the button to change the time setting value, until the required time (zui small value 1h), and then press the set key to deposit the setting point into the microcontroller, at this time the left display window shows the measurement time, the right display window shows the set timetiming function: When the instrument is powered, the timing function starts to startAt the end of the timing, the output is offThe heater and refrigeration compressor stop working and the temperature in the incubator will gradually reach the ambient temperature of the outside environment3) Status indication: After the setting is complete, the device runs according to the set parametersWhen the measured temperature is below the set temperature, the device enters a heating state and the heating light is onConversely, when the measured temperature is higher than the set temperature, the cooling indicator is on and the equipment enters the cooling stateWhen the measured temperature is above the set temperature of 4 degrees C, the alarm indicator is on and the buzzer is whistling4) parameter modification: in the run to modify the temperature, time parameters, and then according to program 1, 2 to modify 5) Quick setting: in the setting of parameters, one of the three numbers flashing, if you press the key, the last digit of the set value plus 1, if you press this key does not open, about 3 seconds later, the set value added 1 consecutively, if you press the key, then the setting value minus 1, if you hold the body does not release, about 3 seconds after the set value minus 1 (ii) humidity setting 1) humidity setting: press the "humidity set" key, the window "upper limit set" light (red), at this time press the button to change the humidity setting to the desired humidity, and then press the "humidity set" button, the window "lower limit set" indicator (green) light, at this time press the button or button to set the lower limit humidity, and then press the "humidity set" button "Lower limit set" humidity value and "upper limit set" humidity value difference of 2% (recommended value of 1% to 5%), the user can also be set according to the actual situation 2) parameter modification: to modify the humidity parameter in the run, and then according to program 1 to modify 3) quickly set: in the setting parameters, if you press the key then set the last digit plus 1, if you press this key does not let go, about 3 seconds later, the set value added 1 consecutively; 4) Status indication: When the humidity in the box does not reach the set lower humidity, the work and humidification indicator son, humidifier work, humidity rises to the set lower limit humidity and then intermittently humidify, until the upper humidity stops humidification Allows humidity to fluctuate within the range of demand When the humidity gauge displays EFF, it is an overflow display, and the actual humidity is outside the humidity meter display range At this point, the outside door of the incubator can be opened, usually after a period of time will automatically resume the display Humidity can be humidified if the humidity shows low