Villa waterproof to do so, absolutely no problem!

With the improvement of quality of life, the purchase of villas more and more rich, villa decoration and our ordinary house decoration can not be the same, need to pay attention to more points, the need for construction details are also many, villa decoration first need to consider the problem is villa waterproof.
of the villa is roughly divided into several parts: kitchen waterproof, balcony terrace waterproof, basement waterproof, exterior wall waterproof,
roof waterproof
.
kitchen waterproof
1, to ensure that the floor of the bathroom is flat, to paint the first paint, paint to be firmly combined with the grass, the thickness is moderate

. For better results, wait for the first paint to dry out and then paint for a second time. In order to ensure that the waterproof coating after construction is not damaged, it is required to lay a protective layer on the surface of the waterproof coating, the protective layer should be firmly combined with the grass roots. After the completion of construction, closed water tests are required, and waterproofing works need to be carried out again if they are not qualified.
2, kitchen sink should be sealed with sealant around the gap, to prevent water penetration, otherwise it will affect the life of the cabinet. The cabinet drainage pipe interface should be sealed to prevent water spillage.
3, in the general
bathroom waterproof
treatment, bathroom walls, especially shower room area waterproof should be up the ground more than 1.5m, kitchen wall waterproof should be up to 20cm or more along the ground. If the bathroom wall is a non-load-bearing light body wall, because of the characteristics of the lightweight wall, we need to fill the entire wall with waterproof paint.
balcony terrace waterproof
1, villa balcony terrace floor waterproof, first of all to ensure that the ground has slope, the lower side is equipped with drains. The terrace floor should be 3cm-6cm below the indoor floor floor and be a gentle slope to ensure that it can flow rainwater into the drain.
2, do balcony waterproof, need to choose a strong extension, good anti-aging ability and high pull strength waterproof materials, because the balcony long-term exposure to external environment, easy to be affected by temperature. In addition, if only flexible waterproof, a little hard will be waterproof layer punctured. Only do mortar waterproof, balcony ground grass stretch deformation waterproof layer will crack, so it is best to do just soft waterproof combination construction.
3, outdoor socket should have waterproof cover, waterproof cover around the application of sealant filling, to prevent rainwater from the socket through the pipe into the room. The socket for outdoor use should have a waterproof cover to prevent rainwater from flowing into the room through the socket pipe.
basement waterproof
because the basement is easy to return to moisture, so not only to do waterproof, but also to do moisture treatment. Although the developer has done a waterproof, but we also need to do waterproof in the decoration, after all, developers do in order to save costs will not consider too much for us, so we do waterproof in the decoration need to be more attest.
1, external anti-external paste method construction: external anti-external waterproofing method, that is, on the base plate mat layer laid coil waterproof layer, and after the construction of the enclosed structure wall, and then the facade coil (waterproof layer) directly laid on the outer wall of the enclosed structure, and then take protective measures of the basement waterproof construction method.
2, the construction of the outer defense internal affling method: the outer defense internal affling method is in the base plate mat layer will be permanent protection wall all finished, and then the coil (waterproof layer) on the permanent protective wall and the base plate mat layer, to the basement waterproof layer all finished, and finally poured the surrounding structure concrete. This method is a waterproof scheme used when the construction environment conditions are restricted and it is difficult to implement the external external paste method.
3, wall ground seams, pipe ground seams, are prone to problems, decoration can be done in the upper and lower water pipe cement root. Brush 10 to 20 cm of polyurethane waterproof coating from the ground up, and then the ground to redo polyurethane waterproof, plus the original waterproof layer, the composition of a composite waterproof layer, to enhance water resistance.
Exterior wall waterproof
If the outer wall is not insulation:
1, the outer wall with paint finish, waterproof layer should be located between the looking flat layer and paint finish layer, waterproof layer should be polymer cement waterproof mortar or ordinary waterproof mortar.
2, the outer wall using block finish, waterproof layer should be located between the find layer and block bonding layer, waterproof layer should use polymer cement waterproof mortar or ordinary waterproof mortar.
If the outer wall is insulate:
1, when using paint or block finish, the waterproof layer should be located between the insulation layer and the wall base, the waterproof layer can be used polymer cement waterproof mortar or ordinary waterproof mortar.
2, if there is a basement, the outer wall waterproof layer should be connected with the basement waterproof layer.
is not recommended to scrape putty in large quantities when painting the exterior walls. If you really need to scrape putty in batches, it is not appropriate to scrape too thick in batches. This is because the putty layer and the wall bottom material is different, the expansion coefficient is different, easy to cause cracking, or even fall off.
roof waterproof
1, clean the surface, and the cement adhesive preparation.
2, if the roof grass is uneven, need to be in accordance with the design of hanging wire to find slope treatment, should also be retractable seams installed.
3, the roof waterproof seam construction, with cement binder waterproof layer and additional layer and other layers bonded together, the width is about 10 cm. When the waterproof coils are ready, lay them out on the roof surface.
4, waterproof coil paved, should be on the waterproof surface to do another cement mortar protection layer, thickness of about two centimeters, can be divided into two construction, the surface requirements are flat, and to sprinkle water for conservation.
above is about the villa waterproof construction matters, small editor for everyone to organize the above content, for reference only. If you have more waterproof engineering questions, welcome to online consultation
Zhejiang waterproof company
-Zhejiang open source waterproof technology Co., Ltd. official website.