Wall construction | how to use gypsum board partition wall? Is this problem still bothering you?

Core tip: gypsum board is widely used in decoration The real function of gypsum board partition wall is to divide indoor space The utility model has the advantages of simple structure, convenient processing and installation Then there will be a lot of friends to ask, how should we use gypsum board partition? Next, let the editor explain to you in detail! Gypsum board partition installation methods: 1 First of all, we need to set out the wall line on the ground according to the wall position determined in the design, and lead the line to the ceiling and side wall 2 Then clean the contact part between the building and the ground Then apply to the interface treatment agent and pour and vibrate C20 concrete wall pad Ensure wall gasket Which is the price of Dajin diatom mud Recommended brief introduction: which is the price of Dajin diatom mud? How to buy genuine diatom mud? Guangdong diatom mud agent suggests placing a basin of cold water in the air conditioning room, so that the diatom mud wall can breathe effectively The feature of the breathing wall is obvious When the indoor air is dry, the diatom mud wall will release the absorbed water quickly Put it out to help regulate the indoor dry humidity It is suggested to place a basin of cold water in the air conditioning room, so that the wall of diatom mud can breathe effectively The feature of the wall that can breathe is obvious When the indoor air is relatively dry, the wall of diatom mud will absorb the water Paint Home News: gypsum board is widely used in decoration The real function of gypsum board partition wall is to divide indoor space The utility model has the advantages of simple structure, convenient processing and installation Then there will be a lot of friends to ask, how should we use gypsum board partition? Next, let the editor explain to you in detail! Gypsum board partition installation methods: 1 First of all, we need to set out the wall line on the ground according to the wall position determined in the design, and lead the line to the ceiling and side wall 2 Then clean the contact part between the building and the ground Then apply to the interface treatment agent and pour and vibrate C20 concrete wall pad Make sure the upper surface of the wall pad is flat and smooth, and the two sides are vertical 3 The second is to install the keel along the ground and along the top After the installation of the keel along the ground and along the top is completed, fix it with shooting nails The middle distance of the shooting nails is 900mm The position of the shooting nails should avoid the concealed pipes that have been laid 4 Finally, the vertical keel shall be installed According to the previously determined vertical keel spacing, the grid marking shall be carried out along the ground and along the top keel The vertical keel corresponding to the marking is arranged by the wall If there are doors and windows on the partition wall, they should be arranged from the door and window to one side or both sides When the distance between the last keel and the wall is larger than the specified keel distance, a keel must be added Fix the door and window frame and install the gypsum board: when the door and window frame is in place according to the design position, it shall be connected with the vertical keel, along the ground and along the top keel During the installation of gypsum board, the vertical arrangement shall be adopted, and then the gypsum boards on both sides of the keel shall be staggered, and then the gypsum board and the keel can be fixed with self tapping screws Secondly, the self tapping screw should be at least 10 mm away from the edge of the gypsum board wrapped by paper, and at least 15 mm away from the edge of the cut board Here, we should pay attention to that the screw cap should be buried in the human board, but it can not damage the paper It's better to be clear that the middle distance of self tapping screw should be 250mm around the board and 300mm in the middle of the board Treatment of concealed joint of gypsum board partition wall: 1 First, clean the floating soil and dust in the joint, and use a small knife to insert putty into the joint to make it flush with the board joint 2 Press and scrape with a knife from the top to the bottom, and then squeeze the excess putty out of the mesh Then use a big knife to scrape the putty, bury the fiberglass tape in the putty layer, and fill the wedge edge of the gypsum board with leveling This is the end of Xiaobian's introduction on how to use gypsum board partition wall I hope that Xiaobian's introduction can help you Home of coatings is specialized in coatings, diatom mud, paint coating, coating technology, fire retardant coating news and coating, diatom mud, paint coating, coating technology, fire retardant coating decoration knowledge and decoration renderings,