-
Categories
-
Pharmaceutical Intermediates
-
Active Pharmaceutical Ingredients
-
Food Additives
- Industrial Coatings
- Agrochemicals
- Dyes and Pigments
- Surfactant
- Flavors and Fragrances
- Chemical Reagents
- Catalyst and Auxiliary
- Natural Products
- Inorganic Chemistry
-
Organic Chemistry
-
Biochemical Engineering
- Analytical Chemistry
- Cosmetic Ingredient
-
Pharmaceutical Intermediates
Promotion
ECHEMI Mall
Wholesale
Weekly Price
Exhibition
News
-
Trade Service
The isolated reactor cooling system is equipped with various reactors and reactors for temperature control.
It is a container used for chemical reactions and is widely used in chemical production
.
According to the specific use of different reaction conditions, there are differences in technical indicators such as material, temperature, pressure, etc.
, and there are various heating methods, such as steam, electric heating, heat transfer oil,
etc.
1.
The performance of compression should not be affected by high temperature and ambient temperature at room temperature
.
If the temperature is too high, the output air volume of the compressor will be reduced
.
The equipment should be placed in a spacious place, and the small space is not conducive to later repair and maintenance, especially the radiator (condenser) of the compressor should be regularly maintained and kept clean
.
2.
The site voltage should be kept stable, otherwise the current will be too large or too small, and the compressor will be damaged when working under these conditions for a long time
.
It should be built on a hard floor, and the foundation plane must be leveled before installation to avoid the compressor vibrating and causing noise
.
3.
In the process of temperature control, correct operation and reasonable handling of faults are conducive to the maintenance of the compressor and prolong the service life
.
In the process of cooling and heating, it is not advisable to start the compressor frequently, and the interval between compressor startup is 15 minutes
.
4.
When the equipment is in trial operation, strictly check the running direction of the compressor.
When it is found that it is reversed, it should be stopped immediately, cut off the power supply, and switch any two of the three-phase lines before restarting, otherwise the compressor will be damaged
.
During the operation of the industrial cooling and heating integrated machine, the protection systems such as the compressor safety valve are regularly inspected to ensure that it is sensitive and reliable
.
5.
If there is a lot of dust in the air around the equipment, it is necessary to add a filter device.
At the same time, the air is not allowed to contain flammable gas and corrosive gas, so as not to cause explosion or internal corrosion
.
Generally speaking, it is necessary to ensure that the relative humidity of the air is low and the ventilation is good
.
It is a container used for chemical reactions and is widely used in chemical production
.
According to the specific use of different reaction conditions, there are differences in technical indicators such as material, temperature, pressure, etc.
, and there are various heating methods, such as steam, electric heating, heat transfer oil,
etc.
1.
The performance of compression should not be affected by high temperature and ambient temperature at room temperature
.
If the temperature is too high, the output air volume of the compressor will be reduced
.
The equipment should be placed in a spacious place, and the small space is not conducive to later repair and maintenance, especially the radiator (condenser) of the compressor should be regularly maintained and kept clean
.
2.
The site voltage should be kept stable, otherwise the current will be too large or too small, and the compressor will be damaged when working under these conditions for a long time
.
It should be built on a hard floor, and the foundation plane must be leveled before installation to avoid the compressor vibrating and causing noise
.
3.
In the process of temperature control, correct operation and reasonable handling of faults are conducive to the maintenance of the compressor and prolong the service life
.
In the process of cooling and heating, it is not advisable to start the compressor frequently, and the interval between compressor startup is 15 minutes
.
4.
When the equipment is in trial operation, strictly check the running direction of the compressor.
When it is found that it is reversed, it should be stopped immediately, cut off the power supply, and switch any two of the three-phase lines before restarting, otherwise the compressor will be damaged
.
During the operation of the industrial cooling and heating integrated machine, the protection systems such as the compressor safety valve are regularly inspected to ensure that it is sensitive and reliable
.
5.
If there is a lot of dust in the air around the equipment, it is necessary to add a filter device.
At the same time, the air is not allowed to contain flammable gas and corrosive gas, so as not to cause explosion or internal corrosion
.
Generally speaking, it is necessary to ensure that the relative humidity of the air is low and the ventilation is good
.