40kg plant extract vacuum belt dryer

40kg plant extract vacuum belt dryer evaporation capacity: 40-55kg/h, heat exchange area: 60㎡, feed capacity: 70-130kg/h
.

Solid content of raw materials: more than 40%, dry powder moisture content: ≤4%.


Temperature: 40~130°C adjustable, process temperature control: ±2°C
.

Can reach the vacuum degree: 1000Pa, working vacuum: 1000-3000Pa
.

Drying time: 35 minutes to 70 minutes adjustable
.

After drying, the particle size of the material meets the requirements: 16~60 mesh adjustable
.

The feed pump adopts one-to-one arrangement, and the feed amount is continuously adjustable
.

Equipment operation comprehensive performance requirements: the equipment is equipped with good control, vibration reduction, transmission, transmission, transmission, cooling, lubrication devices, under continuous full load production conditions, stable operation, performance to meet the design requirements
.

The drying operation of the vacuum belt dryer is automatic, the parameters can be set, and the entire program
is automatically completed according to the set parameters after starting.

The refrigeration equipment adopts water cooler
.

The body support of the device distributes the load evenly across the
ground.

The wall thickness of the cylinder body is 8mm
.

The material is SUS304 stainless steel
.

Direct contact and metal parts of the cylinder (including seals, screws, gaskets, etc.
) are made of the required SUS304, non-metallic parts are made of PTFE, silicone rubber and other GMP-recognized non-toxic materials, sealing materials using high temperature resistance, corrosion resistance, not easy to fall off, in line with GMP requirements of the material; The inner surface of the equipment is mechanically polished, and the surface roughness Ra≤ 0.
8μm
.

The equipment cylinder is provided with a large aperture observation window, which can be heat-resistant, corrosion-resistant, tightly sealed, etc.
, and can clearly observe the drying process in the dryer for workers to operate and use, and the diameter of the sight glass is not less than DN300, and the number is not less than 12 and equipped with lights
.

The cloth device should be able to evenly distribute the material on the feeding belt, and the width of the cloth can be adjusted
.

The conveyor belt is set to 6 layers
.

Track speed can be continuously adjusted by frequency conversion; The track runs smoothly, there is no scratching and stagnation, and the running speed can be adjusted arbitrarily; Tracks should be easy to inspect and service
.

The conveyor belt adopts PTFE belt, which does not penetrate the material, is not easy to bond the material, has a high temperature resistance of more than 200 °C, and has a service life of more than
one year.

The conveyor belt roller is made of special structure to prevent secondary pollution of the material on the track and insoluble substances
.

Ensure that the operation process is not wet, easy to clean, in line with food and drug hygiene requirements
.

The equipment has online and segmented cleaning functions, the number of internal nozzles and rotating spray balls and the installation position should be designed to ensure the quality of cleaning, to ensure the cleaning
of the cylinder.

The cylinder in the main cylinder of the equipment cylinder must be made of 304 stainless steel, and the cylinder outside the cylinder body adopts SMC equivalent to the imported brand
.

The heat exchange plate adopts zigzag channel design to ensure the uniformity of the heating distribution of the heat exchange plate, the pressure resistance is 0.
8Mpa (warranty of 5 years), and the pressure test record
should be tested before leaving the factory.

The conveyor belt drive should have an active guiding device, which can automatically correct the deviation when the conveyor belt is deviated, and the correction distance is ± 10mm, ensuring the long-term normal operation of
the track.

The sealed doors at both ends of the cylinder should ensure that the vacuum does not leak during operation, and the door opening structure at both ends should ensure the smoothness and safety
of the door opening.

The dry powder is discharged by screw to the pulverizer, and the crushed product is transported to the dry powder storage tank
.