echemi logo
Product
  • Product
  • Supplier
  • Inquiry
    Home > Active Ingredient News > Drugs Articles > Brush resistance tester test method analysis

    Brush resistance tester test method analysis

    • Last Update: 2022-09-14
    • Source: Internet
    • Author: User
    Search more information of high quality chemicals, good prices and reliable suppliers, visit www.echemi.com
    Brush resistance tester evaluates the anti-scrubbing ability of the painted surface tested by brush, sponge, cleaning cloth, sandpaper or other methods, and is applied to the scrubbing resistance test of interior wall coatings, floor tiles, shower rooms and furniture surfaces, which is the test equipment independently developed and produced by Shanghai Qianshi Precision Electromechanical Technology Co.
    , Ltd.
    , which is cost-effective and has complete
    after-sales service.

    Conforms to the standard: paint varnish: ISO 11998; interior wall coating: ASTMD3450, ASTMD4213, ASTMD4828, ASTMD2486; Floor wax: ASTMD1792, ASTMD3206, ASTMD3207; Building materials coatings: GB/T9266-88 "Determination of brush resistance of architectural coatings" Test method A: Thoroughly stir the test paint to remove all air bubbles and particles
    .

    For each coating, 3 strips of coating
    need to be pulled out.

    Scrape off the paint
    using the same 0.
    18mm gap film coating model on the black plastic panel.

    The application time from one end to the other is about 3 to 4 s, preventing the formation of bubbles or cavities
    in the film.

    Placed horizontally in air at 23±2 °C and 50±5% relative humidity for 7 days
    .

    Soak the brush in water
    .

    Place the sample plate in the carrier tray of the scrub tester
    .

    Make sure the copper gasket is smooth and burr-free, positioned
    perpendicular to the brush path.

    Gently wipe the sample plate and place it above the copper strip with the paint face facing upwards
    .

    Make sure there are no defects in the sample membrane above the copper sheet and that the test area is horizontal
    .

    Place the positioning frame in the dish and clamp it.
    To start the trial, it should be confirmed that the brush has been pretreated with 400 cycles
    .

    Remove the brush and shake off excess water
    .

    Stir the scrub medium evenly, remove about 10g and spread evenly over the
    sample.

    Place the brush at one end
    of the path.

    Wet the panel
    with 5 mL of water in the path of the brush.

    Start testing
    .

    After 400 cycles, if there is no failure, remove the brush (do not rinse), add 10 g of agitated scrubbing medium again, and add 5 mL of water to the path of the brush, then continue scrubbing
    .

    When a continuous thin line is scrubbed on the copper strip at a width of 12.
    7mm, the number of cycles is recorded
    .

    If necessary, stop the machine and wipe the gasket area to determine if the end point
    is reached.

    Test two coatings
    .

    If the difference between the two results exceeds 30% of the average, test a third coating
    .

    Discard one of the three results with too much deviation and average
    the remaining results.

    Test Method B: Mix the test paint and reference paint thoroughly to remove all air bubbles and particles
    .

    Follow the procedure described above and pull out two coatings
    side by side.

    Prepare three sets of sample plates
    for each test paint (including reference paint).

    The coating should be pulled out as simultaneously as possible, and the coating part should be in the middle
    of the sample.

    Dry under standard conditions for 7 days
    .

    Place the sample plate and 2 copper strips in a similar method to Method A and fix well
    .

    To start the trial, it should be confirmed that the brush has been pretreated with 400 cycles
    .

    Remove the brush and shake off excess water
    .

    Stir the scrub medium evenly, remove about 10g and spread evenly over the
    sample.

    Place the brush at one end
    of the path.

    Wet the panel
    with 5 mL of water in the path of the brush.

    It is recommended to change the position of the test paint and the reference paint in the two sets of sample plates to test
    .

    That is, one sample plate has a reference paint on the right side, and a reference paint
    on the left side of the second sample plate.

    Record the number of cycles
    of continuous thin lines (scrub marks) above the test paint and the reference paint, respectively.

    If necessary, stop and wipe the copper strip area to determine if the test endpoint is reached
    .

    Test two coatings
    .

    If the difference between the two results exceeds 30% of the average, test a third coating
    .

    Discard one of the three results with too much deviation and average
    the remaining results.

    This article is an English version of an article which is originally in the Chinese language on echemi.com and is provided for information purposes only. This website makes no representation or warranty of any kind, either expressed or implied, as to the accuracy, completeness ownership or reliability of the article or any translations thereof. If you have any concerns or complaints relating to the article, please send an email, providing a detailed description of the concern or complaint, to service@echemi.com. A staff member will contact you within 5 working days. Once verified, infringing content will be removed immediately.

    Contact Us

    The source of this page with content of products and services is from Internet, which doesn't represent ECHEMI's opinion. If you have any queries, please write to service@echemi.com. It will be replied within 5 days.

    Moreover, if you find any instances of plagiarism from the page, please send email to service@echemi.com with relevant evidence.