Instructions for small pill making machine of traditional Chinese Medicine

Small Chinese medicine pill making machine can produce honey pill, concentrated pill, water honey pill, water pill, pill food, and can also coat and dry Make the pills uniform and beautiful It is especially suitable for small-scale pharmaceutical factories, large and medium-sized pharmaceutical factory trial production rooms, traditional Chinese medicine research institutes, hospitals, private clinics, traditional Chinese medicine stores, precious tonic on-site processing and sales points, and the whole machine is made of stainless steel, meeting GMP standards And small size, low energy consumption, high efficiency, low noise, no pollution, simple operation, safe and reliable, the machine uses 220V lighting electricity, electrode is convenient Technical parameters: ◆ pelletizing specification: Φ 4, 5, 6, 8mm ◆ motor speed: 1440 rpm ◆ working speed: 50 rpm ◆ output: 2-5kg / h ◆ power rate: Motor: 0.18kw, electric heating: 1kW, Voltage: 220V ◆ external dimension: 550 × 330 × 250mm ◆ weight: 35kg Manual: I machine instructions 1 before using the machine, remove the upper cover shell and gearbox cover (as shown in the figure) Add several drops of water-free edible oil at each oil hole, and then use medical alcohol to scrub the four rollers and the parts contacting with the pill for disinfection 2 Reinstall the upper cover shell and gearbox cover, connect the power supply, turn on the switch, and turn the machine for 1-2 minutes 3 Put appropriate amount of the evenly distributed pellet into the extrusion slot, press the cake, then put the cake into the strip slot to form a strip, and then put the made strips one by one horizontally in the pill making slot to directly rub them into pills 4 Water pill: put the noodles into the coating machine, and gradually put the rice soup into it After the granule is formed, spray the edible water at intervals to gradually roll the pill 5 Coating: after the pill is made, it can be put in the water pill coating device and wrapped into white, red and other coats 6 Drying method: after the pill is made, put the pill into the water pill coating device for electric heating and drying It can also be dried by the hot air of the hair dryer or directly in the sun 7 Polishing method: put the pill in the water pill coater and roll continuously The longer rolling time is, the smoother the surface is 2 User's notice 1 This machine is suitable for the environment temperature of - 5 ℃ to 40 ℃, and the relative humidity is less than 90% There is no conductive dust and corrosive metal gas around, and it is placed in a ventilated and clean position 2 During operation, there shall be no other irrelevant items on the worktable The pelletizer shall be placed on a stable platform When the power supply voltage is confirmed, the power supply shall be close to the platform, and the power socket shall have a reliable grounding wire It is strictly prohibited to pull the power cord forcibly to prevent man-made overturning, damaging the pelletizer and other accidents 3 After the machine is used, remove the socket head cap screw as shown in the figure, divide the upper part and the lower part with the roller as the boundary, remove the four rollers, and scrub them with medical alcohol Or change the roller with different specifications according to the requirements of shot making It can be installed and reset as shown in the figure 4 When scrubbing with medical alcohol and replacing the pill making roller and strip clutch roller, the main power must be cut off and the power plug must be pulled out, 5 During the operation of pelletizer, it is strictly prohibited to contact the pelletizing roller and strip clutch roller with hands, brushes or other tools to avoid finger injury It is strictly prohibited to electrify the pelletizer without the protection of upper cover and gearbox cover to avoid unnecessary personal accidents 6 If the power cord is damaged (such as exposed bare wire), special power cord must be used Purchase and replace it in the maintenance department of the local office In case of failure of switch or socket, it is necessary to stop using It is strictly prohibited to change the line for further use The head or socket of the same specification shall be replaced in time to avoid mechanical and personal accidents 7 Proportion making method: for the mixing and making method of honey pill, water pill and coated drug surface, please refer to the reference formula of pill making 8 The matching pulverizing equipment of this machine can choose the lh-08b continuous flow pulverizer or 400g-500g swing pulverizer 9 When the water pill coater is not in use, it can be removed and washed directly (as shown in the figure), rotated clockwise and pulled out Put it in a reliable and clean place for use Apply a small amount of clean edible oil on the exposed part of the water pill coater shaft to prevent floating rust It is forbidden to wash the whole machine or electric heater directly with water When the machine is not in use, it must be placed in a dry, clean and ventilated place During the use of electric heater, it is strictly prohibited to contact with water to prevent electric conduction and personal accidents such as electric shock