echemi logo
Product
  • Product
  • Supplier
  • Inquiry
    Home > Coatings News > Resin News > The following points should be paid attention to in the inspection and storage of paint!

    The following points should be paid attention to in the inspection and storage of paint!

    • Last Update: 2020-10-07
    • Source: Internet
    • Author: User
    Search more information of high quality chemicals, good prices and reliable suppliers, visit www.echemi.com
    If all kinds of coatings are stored improperly, precipitation, dry knots, glue and so on will occur. Such as water-based lactamine method temperature is lower than 0 degrees C, easy to destroy the emulsification state, so that its spoilage scrap, so it is necessary to understand the paint view, quality identification and inspection, master the storage and storage methods of coatings.
    All kinds of coatings, auxiliary materials normal appearance and inspection
    kinds
    normal appearance
    inspection method
    water-soluble coatings
    no turbidity phenomenon, with sticky research by hand, after stirring pigment suspension uniform, there are Normal slurry state
    e.g. abnormal odor, flocculation becomes murky, can be taken out a little trial, direct observation of its effect
    synthetic resin coating
    should be no hard blocks, do not condense, do not separate after stirring in a uniform state, natural conditions can be dry, cured, Mold-free state
    such as the appearance of lumps, condensation, separation state, after stirring can not be improved, you can take out a little trial, direct observation of its effect
    fudder
    talc powder: fine particles, color is not very white
    Smooth delicate sense, wash with water is off
    big white powder: particles than talcum powder thicker, color than talc powder
    white
    The particles are coarser, some are gray-white
    when studying, there are particles, but the water can be chemicalized
    zinc white (zinc oxide, Lid powder, lead white): color white has a harsh feeling, particle fineness between the big white powder and plaster powder
    Wipe off
    commonly used all kinds of paint, thinner normal appearance and inspection

    kinds
    normal appearance
    inspection methods
    varnish class
    clear and transparent, lighter color, proper consistency, the lighter the color, the more transparent the better . Phenolic varnish for light yellow, brown to yellow brown, transparent oily liquid, alcoholic acid varnish for light red brown transparent oily liquid Can also be sampled into a clean and dry color tube, with different turbidity of the standard liquid comparison
    paint class
    open cover after the surface has no skin (allowing slight skin), only a thin layer of oil or thinner, thicker below, but once stirred can be fully mixed. Color meets the requirements, the viscosity is moderate
    such as the discovery of precipitation, skin, thickening, thickening and other phenomena indicate changes. After stirring the paint, with a stick to provoke paint observation, paint silk color should be free to land without interruption, such as interruption of retracting shows that the paint quickly glued into
    raw paint class
    milky white or grayish-yellow viscous liquid, with a strong acid flavor
    After painting the color from white to red, from red to purple, and finally into a bright, hard paint film
    disist class
    good quality thinner should be water white clear transparent liquid, no impurities, no suspension, no Odor; normal nitrodi thinner has banana flavor, alicic acid thinner has aromatic aroma, amino thinner should have a mild alcohol taste of butanol
    normal diluent should have a certain rate of volatility, after volatility should not leave traces of residues. Can drop a little thinner on the filter paper, after a few can check whether all volatile (with or without residual impurities); Mix a small amount of thinner with the corresponding resin or paint to see if it is soluble
    commonly used paint descension identification and treatment methods
    name
    phenomenon
    cause
    treatment method
    turbidity
    more commonly seen varnish or varnish. Generally mild turbidity, there is also thickening phenomenon, serious for white paste
    thinner improper selection or excessive dosage, room temperature is too low, relative humidity is too large, container closure is not strict, containing moisture, lead drying agent dosage too much
    Turbo fuel-saving, butanol or benzene cyclic hydrocarbon solvents, heated to 60-65C with water insulation, room temperature controlled at 18-25C, relative humidity at 65%
    5%
    thickening
    viscosity increased, thickened, in severe cases Frozen glue-like
    paint is too acidic, react with alkaline dyes, the finished product polymerization is excessive, the temperature is too hot, too cold, container leakage, leakage
    room temperature is maintained at 18 to 25C paint water isolation heating, alkyd amino paint can be added to the solvent 25% of butt alcohol
    color change
    varnish category: black red, red-brown
    -color paint category: up and down color is not consistent, gold powder, silver powder blackened
    varnish class: solvent hydrolyzed and iron container anti
    should
    ; Paint contains acidic resin
    color paint category: pigment fading, metal pigment greening, pigment precipitation
    Now in use, varnish can be added a little phosphoric acid
    recipitation
    varnish category: the bottom layer is deposited with a variety of impurities or insoluble substances, the upper paint material is intact
    color paint class: in general sediment can Crushed, in severe cases must be shredded
    varnish class: paint with impurities or insoluble substances, lead drying agent in storage too cold or moisture, solvent improper use
    color paint class: pigment density, particles too thick, Too many body pigments
    varnish class: filter off impurities
    color paint class: regularly repeated inversion, use when fully stirred, after the lump re-research and deployment or used in non-important parts
    container deformation
    container bulging, expansion
    days of heat, the container temperature is too high, the paint becomes gaseous
    hether at the lower
    crust.
    open the paint barrel, there is a thin layer of skin on the surface, sometimes small particles or all the gel phenomenon
    the container is not tightly closed, the surface of the coating and air contact, drying agent plus too many people. Storage time is too long
    before use, the paint is refiltered, the paint is leftover in the paint surface with a thinner drying agent with part of zinc, calcium drying agent
    flating
    drying: hard gel, coarse increase or frozen glue
    false thickness: thick appearance
    oxides and acidic natural resin paint meet, oil and liqueur polymerization excessive, latex water-soluble, Salty substances in pigments, too much drying agent, too much pigment in paint In particular, the use of zinc oxide, zinc tantalum white, carbon black and other pigments
    once dried can not be used, this kind of paint should not be stored for too long, by mechanical stirring to add a small amount of organic acid can return to normal, after stirring will be restored to its original condition, stop stirring is still false thick, However,
    paint storage and safety protection
    material name
    storing method
    Precautions oily paint
    olate paint
    polyurethane paint
    oil varnish.
    polyurethane varnish
    oily filler
    ol soluble hydrogen
    putty
    asphalt
    on the shelf, should be marked. To avoid long storage times and badness, the new material should be placed behind
    the lid should be tightened to prevent volatility and skining. Constant temperature makes the coating viscosity suitable. Place heavy containers underneath in case of handling difficulties. Canned pigments and materials should be placed upside down on a regular basis to prevent precipitation
    lotion coating
    lotion varnish
    acrylic paint
    color paint
    chalk
    dry pigment
    cedar plaster
    paste powder
    powder filler
    placed on the shelf, marked. The new material is placed behind the first stored items, cannot be frozen
    small pieces on the shelf, large pieces on the floor mat board, scattered material placed in a covered box
    to prevent freezing. Water-based coatings have a storage period and must be used up within a
    should prevent moisture. Pay attention to the gypsum storage period, moisture-proof to prevent condensation
    ol soluble paint dispassionate agent
    put on the shelf
    temperature above 15C will cause expansion, resulting in sudden out of the container. Prevent open flames
    paraffin
    phenol oil
    (1) in a switched iron bucket placed on the stand (2) in a screwed tank with a screw port of 5-20 L, placed at a low
    Tighten the lid and place it in a sealed space separate from the main building
    liquid gas
    compressed gas
    petroleum
    culcin coating
    cellulose thinner
    chlorinated rubber thinner
    Alcoholic alcohol
    polychloroformide thinner
    (1) placed on the outside should prevent contact with ice and direct sunlight
    (2) special warehouse structure as follows:
    wall: application brick, stone, concrete or other fireproof materials Building
    roof: apply fragile material auxiliary cover to reduce explosive force
    doors and windows: thickness of 50 mm, outward
    glass: thickness should not be less than 6 mm of wire glass
    ground: concrete floor, should be tilted, Spilled solutions should not be left under the container lighting switch: in order not to cause sparks, they should be installed outdoors
    store according to the most flammable liquid and liquefied petroleum gas storage regulations
    Note: These regulations apply only to materials containing more than
    50L
    This article is an English version of an article which is originally in the Chinese language on echemi.com and is provided for information purposes only. This website makes no representation or warranty of any kind, either expressed or implied, as to the accuracy, completeness ownership or reliability of the article or any translations thereof. If you have any concerns or complaints relating to the article, please send an email, providing a detailed description of the concern or complaint, to service@echemi.com. A staff member will contact you within 5 working days. Once verified, infringing content will be removed immediately.

    Contact Us

    The source of this page with content of products and services is from Internet, which doesn't represent ECHEMI's opinion. If you have any queries, please write to service@echemi.com. It will be replied within 5 days.

    Moreover, if you find any instances of plagiarism from the page, please send email to service@echemi.com with relevant evidence.