echemi logo
Product
  • Product
  • Supplier
  • Inquiry
    Home > Coatings News > Coating Technologies > One way to improve the hiding power of white ink

    One way to improve the hiding power of white ink

    • Last Update: 2021-03-26
    • Source: Internet
    • Author: User
    Search more information of high quality chemicals, good prices and reliable suppliers, visit www.echemi.com
    Increasing ink color density is one of the main methods to increase ink hiding power.
    When printing, you can use specially configured ink color density of 55% titanium dioxide ink (ordinary white ink color density is 25%, titanium dioxide pigment is currently the whitest, covering The most powerful white pigment).

    Although its hiding power after printing is better than ordinary white ink, it still does not meet the requirements.
    Due to the high color concentration, less solvent, and fast drying, it is easy to cause blockage.
    After printing, the ink has poor leveling and chalking, so it should be considered Other methods.

    02 Ink thickness We know that the thickness of the gravure ink layer can reach 8-15μm, but if the gravure white ink layer is only 3-4μm, it will not reach the standard, there will be problems.

    You can investigate from the following aspects.

    (1) Plate cylinder production.

    The engraving depth of the plate cylinder of the supplier has reached the maximum (60μm), but due to its technical limitations, the engraved cells are pyramid-shaped, and the pyramid-shaped cells are easy to block the plate and cause poor ink transfer.

    Therefore, although the ink storage volume is increased, the ink transfer volume cannot be increased.
    At this stage, in order to better transfer the ink, the cells should be prismatic or honeycomb.
    The cells of these two shapes have a large ink storage capacity and are easy to transfer ink.

    In addition, the smoothness of the edge of the cell and the thickness of the chrome plating also affect the transfer of the ink, so the method of printing twice can be considered to solve the problem caused by the plate cylinder.

    (2) The hardness of the embossing rubber roller is too large, and the printing material is soft, resulting in too little ink transfer in the cell.
    The embossing rubber roller with softer hardness should be replaced.

    (3) The printing pressure is small, which causes the ink in the cell to be squeezed and poorly transferred.
    At this time, the printing force should be increased.

    (4) The storage time of the film is too long after the surface treatment, resulting in poor ink wetting and adhesion, so it should be printed in time after the surface treatment of the printing material.

    (5) The pigment concentration of the ink is too large, which causes the drying speed to be too fast and affects the ink application.
    The concentration and viscosity of the pigment should be adjusted appropriately.

    (6) The static electricity of the film is too large during printing.
    After eliminating the static electricity, the electrostatic ink absorption device should be used to increase the ink transfer rate.

    (7) Consider the performance of the printing press.

    After taking the above measures to print, the thickness of the ink layer has increased significantly, but the white ink hiding power still does not meet the expected requirements, so the problem of the gravure ink itself must be considered again.

    The hiding power of 03 pigment dispersion ink essentially depends on the ratio of the refractive index of the pigment to the refractive index of the binder.

    When the ratio is 1, the pigment is transparent; if the ratio is greater than 1, the pigment is opaque, that is, it has hiding power.

    The refractive index of the pigment is affected by the dispersion of the pigment and the difference between the refractive index of the pigment and the binder.

    The higher the dispersion of the pigment and the smaller the above difference, the better the transparency of the pigment.

    ▌The pigment of the white ink used in the test is titanium dioxide.

    Titanium dioxide is a white crystalline powder.
    It is the most opaque of all white pigments.
    It has a refractive index of 1.
    84-2.
    55, high dispersion, good light resistance, heat resistance and alkali resistance.

    Other printing methods use ordinary pigments, thinner ink layers and lower color density can achieve the required covering effect, but gravure printing cannot.

    Gravure ink pigment particle size should be less than 5 μm, and gravure ink is thinner than other printing inks, so it has a large dispersion and high transparency (that is, low hiding power).

    If the titanium dioxide particles used are finer and have a large degree of dispersion, the hiding power will be weak.

    If the desired covering effect cannot be achieved by increasing the granularity, you can only switch to other printing methods.

    If you use an ink made of titanium dioxide with an appropriately increased particle size for printing, the hiding power of the white ink will increase.
    This method saves time and effort than increasing the ink color density and ink layer thickness, and can also reduce production costs.
    This article is an English version of an article which is originally in the Chinese language on echemi.com and is provided for information purposes only. This website makes no representation or warranty of any kind, either expressed or implied, as to the accuracy, completeness ownership or reliability of the article or any translations thereof. If you have any concerns or complaints relating to the article, please send an email, providing a detailed description of the concern or complaint, to service@echemi.com. A staff member will contact you within 5 working days. Once verified, infringing content will be removed immediately.

    Contact Us

    The source of this page with content of products and services is from Internet, which doesn't represent ECHEMI's opinion. If you have any queries, please write to service@echemi.com. It will be replied within 5 days.

    Moreover, if you find any instances of plagiarism from the page, please send email to service@echemi.com with relevant evidence.