What are the adjustment methods of automatic oral liquid filling capping machine

Automatic oral liquid filling capping machine is a filling equipment
specially designed for the new oral liquid bottle.

The design is reasonable, the structure is simple, the operation is convenient and the mechanical bottle out of bottle stop filling device is provided
.

Then, the adjustment method of the automatic oral liquid filling capping machine mainly has the following 1, the adjustment
of the feed and a half.

a.
Adjust the bottle holding plate A on the half of the feed upwards to shorten the adaptation to the bottle inlet stroke; Adjust down to extend
the adaptation to the bottle inlet stroke.

b.
Adjust the positioning bottle position left and right so that the active teeth run to the positive bottle position so that the bottle is smoothly fed into the positioning teeth
.

c.
Adjust the bottle holding plate B so that the width of the bottle inlet ≈ about
22 mm.

2, the adjustment of the vibrator This automatic drop cap adopts the principle of electromagnetic oscillation to drop the bottle cap along the track to the appropriate position
according to a certain motion trajectory.

a.
The vibrator is packaged separately when it leaves the factory, and the lower rail mouth must be aligned with the moving track of the
easy-drawn bottle.

b, the adjustment of the magnet gap: release the screw 1, open the cover, adjust the nut 2, so that the magnet gap is 0.
6-0.
8, and make the vibration sound low cap line speed is appropriate
.

3, perfusion component adjustment, the role of the perfusion component is to make the liquid through the dispenser, check valve, needle timely delivery to each bottle, so the needle into the bottle mouth must be appropriate, and the filling time should also be appropriate
.

a.
Adjust the side cam A to turn or reverse so that the needle is inserted into the bottle mouth
as soon as the empty bottle enters the toothed position.

and lift the needle before leaving the toothed position
.

B.
Perfusion time adjustment: turn the cam B along or reverse the adjustable needle into the bottle mouth immediately after starting the infusion, stop the filling before the needle leaves the bottle mouth
.

c.
Liquid volume adjustment: release nut 1 to adjust the ejector bar to D direction, and the liquid volume increases; Adjust the liquid volume to the C direction to reduce, while adjusting the nut 2 to the F direction to reduce the liquid volume, adjust the increase in liquid volume in the E direction, pay attention to the limit position of the infusion device when adjusting, so as not to damage the infusion, generally the bottom of the perfusion device to the medicinal peck is not less than 15 mm is appropriate, the longer the perfusion time, the better
.

4.
The working principle and adjustment
of the automatic stop filling device.

When moving the tooth plate to move the bottle to the filling liquid of this gear position, the convex surface of the cam 7 and the swing plate 6 leave, the swing plate 6 is pulled by the spring 4, swinging in a clockwise direction, the swing plate 6 drives the pressure bottle bolt 2 downward, until it comes into contact with the bottle 3, at this time the wire rolling head 5 swing plate 6 contact and adjust the adjustment screw 8 so that the ejector rod bolt 1 extends about 4 mm, this gear position appears empty bottle, the bottle press bolt 2 and the rocker 6 continue to move down due to the role of the spring 4, To make the wire rolling head 5 pull the steel wire so that the ejector rod tether 1 out of the elevation rod 9 so can not drive the dispenser work, automatically stop the infusion of liquid
medicine.

5, discharge precautions Because this machine is a bottle filling and locking equipment, so the discharge is capped and sealed, in order to make the bottle after the filling not to overturn, it is necessary to put a number of empty bottles on the discharge hopper in advance before the first bottle is discharged to keep the bottle after the filling smoothly transported to the outlet hopper, and send it to the next process
with the bottle bucket.

6, the lock device is digestion * technology, according to the domestic oral liquid production situation specially designed for the existing specifications of the bottle, so the geometry of the bottle and error has certain requirements, if there are special requirements or other specifications, please communicate
with the technical department of our factory.

7, the adjustment of the lock device a, the capping time adjustment: adjust the cam 3 rotation angle When the perfusion liquid bottle enters the lock position, the lock shaft has been moved and leaves the cap
before moving the tooth close to the bottle.

b, the adjustment of the glanding pressure: the size of the gable pressure is directly related to the quality of the lock, the pressure is too large to break the bottle, the pressure is too small will affect the sealing performance, so the nut 6 should be adjusted according to the actual average height of the bottle, so that the pressure is
adjusted to the best.

c, blade action time adjustment: blade 2 should be close to the bottleneck before the end of the gland, otherwise some short bottles can not achieve the locking effect, release the nut 4 when adjusting, adjust the axis 5, up and down can make the blade 2 action time sooner
or later.

Note that the elasticity of adjusting spring 7 should be greater than the elasticity of spring 8 to keep the bottleneck still consistent
.

d, adjust the lock when paying attention: after the adjustment of each department must pay attention to the lock of each nut, the first valve test with a pull bottle, must take its average height, irregular pull bottle can not enter the lock, so as not to damage the parts
.