Coating process: construction process of acrylic waterproof coating

The core suggestion: acrylic waterproof coating is a thick single component waterborne polymer waterproof coating material, which is based on modified acrylate copolymer emulsion and filled with various fillers and auxiliaries The acrylic high elastic waterproof coating is tough and has strong adhesion The elastic waterproof membrane and the base form a rigid flexible integrated waterproof system to adapt to all kinds of structural deformation and achieve the long-term waterproof and impermeability Acrylic waterproof coating is often used in our daily life, but do you know the construction process and operation points of acrylic waterproof coating? Let's share the construction process of acrylic waterproof coating with you Application scope and advantages of roller ceramic coating Recommended introduction: the surface of ceramic rubber plate used for roller ceramic coating is cast into durable rubber plate by hundreds of independent small ceramic pieces Each ceramic piece has raised characteristics Under general conveyor belt pressure, thousands of unique cast bumps can produce positive traction, prevent slipping and extend the service life of conveyor belt roller At the same time, the bottom layer adopts high-quality rubber, which has strong elasticity and can play a good impact resistance role The scope of application of roller ceramic coating is one three six 83857180 (the same as V) 1 Roller coating in extremely harsh working environment 2 The belt joint is not suitable for fixing with iron buckle; 3 It is suitable for leather Coatings home: acrylic waterproof coating is based on modified acrylate copolymer emulsion as the base, adding a variety of filling materials, auxiliaries by scientific processing of thick single component waterborne polymer waterproof coating material The acrylic high elastic waterproof coating is tough and has strong adhesion The elastic waterproof membrane and the base form a rigid flexible integrated waterproof system to adapt to all kinds of structural deformation and achieve the long-term waterproof and impermeability Acrylic waterproof coating is often used in our daily life, but do you know the construction process and operation points of acrylic waterproof coating? Let's share the construction process of acrylic waterproof coating with you The technological process of acrylic waterproof coating: clean the base course → waterproof layer on the bottom → additional layer on the details → brush the intermediate waterproof layer → lay the reinforcing layer → brush the intermediate waterproof layer → brush the surface waterproof layer → the first water storage test of the waterproof layer → construction of the protective layer and the facing → the second water storage test → project quality acceptance Key points of construction of acrylic waterproof coating: (1) base cleaning: the surface of base must be cleaned carefully It is required to be solid, flat, without sand, and basically dry; the gradient of the base course shall meet the design requirements, without ponding (2) Brush the bottom layer: pour the acrylic coating into an empty bucket for about 2 / 3, dilute with a little water and stir fully, brush the bottom layer evenly with a roller brush, with a dosage of about 0.4 kg / ㎡, and carry out the next process when the hand is not touched (3) Detail additional layer: inlay sealing paste: inlay sealing paste in the groove of the pipe root and other parts according to the design requirements The sealing material shall be tightly pressed to prevent the air from being wrapped, and it shall be firmly bonded with the joint wall, without cracking, bubbling and falling The grooves in the leakage prone parts such as floor drain, pipe root and internal and external corners shall be leveled with acrylic paint Precautions for floor drain, pipe root, internal and external corners and entrances and exits; 1 The temperature shall be higher than 5 ℃ during construction, and it is not suitable for construction in rainy days or when there is open water on the base 2 This product cannot be drunk 3 The waterproof coating shall be completely dry before surface decoration construction 4 The film is completely dry for about 2-3 days The wet environment should be extended properly The water storage test can be carried out after it is completely dry 5 The paint can be diluted with water, and the amount of water added should not exceed 10% of the paint amount Home of coatings is specialized in coatings, diatom mud, paint coating, coating technology, fire retardant coating news and coating, diatom mud, paint coating, coating technology, fire retardant coating decoration knowledge and decoration renderings,